Skip to main content
QWE RC01 pulse
QWE-RC01/pulse

Qbus wireless Easywave remote - 1 button

  • Reliable wireless communication with the Qbus system via the Easywave protocol
  • Easily control any Qbus output with a single press of a button
  • Can trigger any desired output (e.g. lighting, alarm, notification…) via configuration in System Manager III
  • Built-in LED provides feedback during use
  • Automatically sends a “Battery Low” warning
Technical info

By pressing the button on this 1-key remote control, a wireless telegram is sent, which is picked up by the Qbus Wireless interface. By configuring it in the Qbus Configuration software, any Qbus output can be controlled with this remote control.

Frequently Asked Questions

  • How do you read an existing configuration?

    This is a completely different procedure depending on the type of controller.

    • For the CTD controllers this goes as follows:

    In the SMIII via "File" or "Utilities / Setup / SD card", click on "Recover QDB from SD".

    After confirmation you choose the name and location where the file should be saved. The zipped QDB file is then read from the SD card of the CTD and saved. With a positive answer to the question "Unzip and open restored QDB?", All data will then be immediately available. If the data you were still working on was not sent or saved, you will first receive a notification to do so.

     

    • For a CTL controller follow the following procedure:

    Because this controller does not yet have a large memory, only limited data can be recovered. Ao the names are abbreviated to 12 characters and serial numbers are not stored anywhere.

    The first step is therefore to type in ALL serial numbers via SMII via "File / Modules". These 6-digit serial numbers can be found on every module (DIN rail, switch, detector, etc.). For the SWC0x switches, an extra option was provided to have them send their serial number via “Search for modules”.

    When you then click on the "down arrow", you can read all this limited information.

  • Always use the latest software for configuration.

    It is always recommended to use the most recent version. This version supports the newest modules and resolves all known bugs.

    If, for example, you enter a serial number and the correct module information does not appear, you are likely not working with the most recent software.

    A newer version will always be able to open the older files (.QDB) without data loss.

    The latest version of the System Manager software, along with the user manual and version history, can be found in the knowledge center.

Technical info for installers

  • Function description

    The QWE RC01/pulse is a single-button remote control. Pressing the button sends a wireless telegram that is picked up by the QWI/EW. By configuring it in System Manager III, this control can execute an action on another wireless module and/or a bus-controlled module. 

    The QWE RC01/pulse has a built-in battery. If the battery capacity is low, the indicator LED will blink during operation.

  • Technical specifications

    General Specifications

    • Power supply: 1x 3V battery, CR2032
    • Radiated power: 0.14mW
    • Modulation coding: FSK
    • Wireless protocol: Easywave
    • Range: open field: 150m; buildings: 30m
    • Ambient temperature: -20°C to 60°C
    • Maximum humidity: 93%, no condensation
    • Maximum installation height: 2,000 meters

    Physical Specifications

    • Protection grade: IP54
    • Transmitter dimensions: 55x36.5x16 mm
    • Transmitter weight: approximately 17.0g

    CE Marking

    • Qbus declares that this product complies with all applicable European directives and regulations.
    • The EU declaration of conformity can be consulted on our website www.qbus.be.
  • Sizing
  • Explanation of symbols
    Symbool Dubbele isollatie

    Equipment where protection against the risk of electric contact is not only based on basic insulation but also on additional protection such as double insulation or reinforced insulation. There is no possibility for grounding.

     

    Symbool Gevaar Aandachtig lezen

    Before connecting the device, it is mandatory to read the manual of the respective product. ISO7000-0434

    Symbool Gevaarlijke spanning

    Power supply connection (230V) to the power supply connector. IEC 60417-5036

    Symbool CE

    CE conformity. All declarations of conformity are available upon request.

  • Warranty provision

    Standard Warranty Period: 2 years from delivery date.

    The warranty is no longer valid if the module has been opened! 

    Defective modules should be sent without seal along with a description of the defect to our service department:

    QBUS N.V.

    Joseph Cardijnstraat 19

    9420 Erpe-Mere

    Belgium

    T +32 53 60 72 10

    F +32 53 60 72 19

    Email: support@qbus.be

     

General

  • Safety Instructions

    Read the entire manual before installing the module and activating the system. 

    CAUTION

    • The device must be installed and commissioned by a qualified electrician in accordance with country-specific regulations.
    • The device meets the IP54 standard, meaning it is protected against limited dust ingress and against low-pressure water jets from all directions.
    • The device must not be opened other than as described for battery replacement. The warranty provisions are void if the module is opened.
    • Keep batteries out of reach of children.

Installation and wiring

  • Check Battery

    The battery voltage is checked by the module each time:

    • one of the buttons is pressed
    • At least once every 24 hours after sending the last status.

    As soon as the battery status is deemed weak, a “Battery Low” signal is sent at least once every 4 hours.

    Once the battery is depleted, the red LED will blink 3 times briefly at a 20-second interval and the low-voltage telegram will be sent automatically. It is advisable to replace the battery at this point. (see “Replacing the Battery”)

    If the voltage continues to drop, the module will shut itself down and no status changes will be transmitted. 

  • Battery replacement
    1. Insert a small object (for example: a flathead screwdriver) into the slot at the back of the transmitter and open the casing.

    2. Replace the battery. Use only the battery type CR2032.

    Note: Ensure that the positive terminal is visible on top. Keep batteries out of reach of children!

    3. Close the enclosure.

    Note: The connection of the module to the QWI/EW remains intact, and you do not need to take any further steps for this.

  • Troubleshooting

    If the receiver does not respond to this module:

    • Check the battery status.
    • Verify that the wireless connection in the installation is not disrupted between this module and the QWI/EW.
    • Check the configuration of the QWI/EW and whether the link with this module is still active.
    • Ensure that other wireless devices operating on the same frequency or in close proximity do not interfere with the functioning of this product.

    If the LED does not light up:

    • Replace the battery. (Ensure the battery polarity is correct.)