Skip to main content
QWE-ROL01/230

Qbus wireless Easywave motor control module

  • Reliable wireless communication with the Qbus system via the Easywave protocol
  • Wireless control of 230V motors
  • Built-in protection prevents overload or damage to the motor.
  • Up to 920VA resistive or 736VA inductive power – suitable for most tubular motors.
  • Wireless range of 150 meters in open field or 30 meters indoors.
  • Can be invisibly installed in a standard flush-mounted box, behind existing switches, or in suspended ceilings.
Technical info Control

The QWE R0L01/230 is a wireless motor control module for operating a 230V motor using a three-position controller in the Easywave protocol.

Frequently Asked Questions

  • How do you read an existing configuration?

    This is a completely different procedure depending on the type of controller.

    • For the CTD controllers this goes as follows:

    In the SMIII via "File" or "Utilities / Setup / SD card", click on "Recover QDB from SD".

    After confirmation you choose the name and location where the file should be saved. The zipped QDB file is then read from the SD card of the CTD and saved. With a positive answer to the question "Unzip and open restored QDB?", All data will then be immediately available. If the data you were still working on was not sent or saved, you will first receive a notification to do so.

     

    • For a CTL controller follow the following procedure:

    Because this controller does not yet have a large memory, only limited data can be recovered. Ao the names are abbreviated to 12 characters and serial numbers are not stored anywhere.

    The first step is therefore to type in ALL serial numbers via SMII via "File / Modules". These 6-digit serial numbers can be found on every module (DIN rail, switch, detector, etc.). For the SWC0x switches, an extra option was provided to have them send their serial number via “Search for modules”.

    When you then click on the "down arrow", you can read all this limited information.

  • Always use the latest software for configuration.

    It is always recommended to use the most recent version. This version supports the newest modules and resolves all known bugs.

    If, for example, you enter a serial number and the correct module information does not appear, you are likely not working with the most recent software.

    A newer version will always be able to open the older files (.QDB) without data loss.

    The latest version of the System Manager software, along with the user manual and version history, can be found in the knowledge center.

Control

Operations via Qbus Control

  • Screen up/down

Technical info for installers

  • Function description

    The QWE R0L01/230 is a wireless motor control module for operating a 230V motor via a three-position control in the Easywave protocol (UP/STOP/DOWN). When used with the Qbus Wireless Interface QWI/EW, you can utilize the Qbus control options using the Qbus address modes "Shutter 1T" and "Shutter 2T" 

  • Technical data

    General Specifications

    • Power supply: 230Vac / 50 Hz
    • Electrical protection automatic circuit breaker max. C4A
    • Modulation coding: FSK
    • Wireless protocol: Easywave
    • Range: open field: 150m; buildings: 30m
    • Ambient temperature: -20°C to 60°C
    • Maximum humidity: 93%, no condensation
    • Maximum installation height: 2,000 meters

    Maximum Allowable Power

    • Resistive power cos phi = 1: 4A; 920VA at 230Vac
    • Inductive power cos phi = 0.8: 3.2A; 736VA at 230Vac

    Physical Specifications

    • Protection rating: IP20
    • Dimensions: 46x46x25 mm

    CE

    • Qbus declares that this product complies with all applicable European directives and regulations.
    • The EU declaration of conformity is available upon request.

     

  • Sizing
  • Symbol explanation
    Symbool Dubbele isollatie

    Equipment where protection against the risk of electric contact is not only based on basic insulation but also on additional protection such as double insulation or reinforced insulation. There is no possibility for grounding.

     

    Symbool Gevaar Aandachtig lezen

    Before connecting the device, it is mandatory to read the manual of the respective product. ISO7000-0434

    Symbool Gevaarlijke spanning

    Power supply connection (230V) to the power supply connector. IEC 60417-5036

    Symbool CE

    CE conformity. All declarations of conformity are available upon request.

  • Warranty Provision

    Standard Warranty Period: 2 years from delivery date.

    The warranty is no longer valid if the module has been opened! 

    Defective modules should be sent without seal along with a description of the defect to our service department:

    QBUS N.V.

    Joseph Cardijnstraat 19

    9420 Erpe-Mere

    Belgium

    T +32 53 60 72 10

    F +32 53 60 72 19

    Email: support@qbus.be

     

General

  • Safety Regulations

    Read the full manual before installing and activating the module.

    ATTENTION

    • The module must be installed, started, and maintained by a certified electrical installer in accordance with the applicable legal regulations of the country where it is installed.
    • The module must be placed in a location inaccessible to children.
    • Before working on the QWE-ROL01/230, power must be turned off.
    • The warranty becomes void if the module is opened.

Installation and wiring

  • Installation

    Avoid mounting this product in the following locations as it can affect the wireless range:

    • Inside a metal electrical cabinet or enclosure.
    • In the immediate vicinity of large metal objects.
    • On or near the ground.

     

    1. Turn off the power.
    2. Connect the power supply and the motor according to the wiring diagram.
    3. Check all connections.
    4. If everything is connected correctly, turn the power back on.
    5. Once the module is powered, this receiver is in operating mode. The LED is OFF at this point.
    6. Follow the instructions in System Manager III to link this receiver to a QWI/EW module.
  • Power Supply

    NOTICE: DISCONNECT THE POWER SUPPLY TO THE MODULE BEFORE WORKING ON THE MODULE!

    • Turn off the power.
    • Connect the power supply and the motor according to the connection diagram.
    • Check all connections.
    • If everything is connected correctly, turn the power back on.
    • As soon as there is power to the module, this receiver is in operating mode. The LED is OFF at this moment.
    • Follow the instructions in System Manager III to pair this receiver with a QWI/EW module.
  • Troubleshooting

    If the receiver does not respond to this module:

    • Check if the wireless connection in the installation is not disrupted between this module and the QWI/EW.
    • Verify the QWI/EW configuration and whether the link with this module is still active.
    • Ensure that other wireless devices operating on the same frequency or in close proximity do not interfere with the functioning of this product.

    If the module exhibits undesired behavior:

    • The module turns on or off at the wrong moment.
    • The relay briefly engages and then automatically disengages.
    • The module does not respond to any commands despite a good connection between the QWI/EW and this module.

    Then definitely try resetting and re-pairing the module with the QWI/EW using System Manager III.

    Note: The QWE-ROL01/230 is equipped with an internal protection mechanism that cuts off power supply to the motor after 150 seconds. Therefore, the operation time cannot exceed 150 seconds.

  • Reset

    If the receiver does not respond to this module:

    • Check if the wireless connection in the installation is not disrupted between this module and the QWI/EW.
    • Check the configuration of the QWI/EW and whether the link with this module is still active.
    • Check if other wireless devices with the same frequency or operating nearby are not interfering with the operation of this product.

    If the module exhibits undesirable behavior:

    • The module turns on or off at the wrong time.
    • The relay engages briefly and then switches off automatically.
    • The module does not respond to any control input and there is definitely good reception between the QWI/EW and this module.

    In such cases, try resetting the module and re-pairing it with the QWI/EW using System Manager III.

    Note: The QWE-ROL01/230 is equipped with an internal protection that interrupts the power supply to the motor after 150 seconds. The runtime cannot exceed 150 seconds.

Qbus System Manager III Manual Update 04 2025 pdf image 465

For each wireless module it is important that it is enrolled to the gateway (QWI/EW)
An I/O module receives a code from the QWI/EW, an input module sends its code to the QWI/EW.

When you click on “Assign new code”, you will be asked to put the module in programming mode and then click on OK:

Qbus System Manager III Manual Update 04 2025 pdf image 466

When OK is pressed, the QWE-REL01 is assigned a transmission code by the QWI/EW. The module may now return from programming mode.

You can do this by briefly pressing the programming button on the module 3 more times. The programming LED will stop flashing.

Qbus System Manager III Manual Update 04 2025 pdf image 468

By using the “On”, “Off” buttons you can perform a first test to check if the code has been programmed correctly. To test this new module via the qbus I/O’s, it is important that the data is first sent to the controller via the normal way (red upload arrow).