Smart switches Sumum

It is important that you set the correct type for the Tastu switches. In the drop-down list you can choose from SWC01/G, SWC02/G, SWC04/G or, if equipped with a temperature sensor, SWC02T/G or SWC04T/G

The screen above is the programming screen of a switch, showing the 4 commands for the switch. These commands are placed so that the top left field (Key 1) corresponds to the top left of the switch when you are in front of the switch, etc.

Remark: You can verify that the position of the switch is correct by making sure that the serial number on the back of the switch is legible (not upside down).

To program the switch, click the drop-down box next to the first key; there you can select I/O’s that you have already created, or create a new I/O. Look at our knowledge center for creating I/O’s.
 

In the drop-down box below the I/O selection window, you can select the mode of the new I/O you want to create. If you have selected an existing I/O, the mode will already be indicated in that box. Look at our knowledge center for a description of the various I/O types you can select.

As you can see on the screen below, for each key you can choose the color of the standby LED (off color), as well as the color for the operating state (on color), or even disable all colors completely, with the option above each color.

It is recommended to use different colors for different I/O’s - e.g. blue for on/off, yellow for dimmers, green for scenes etc. This will make your system easier to use.

The UP/DOWN and TEST keys on each key next to the I/O allow you to verify that the selected I/O is operational and that it is indeed the one we want to illuminate on the key in question for this particular switch.

The properties option takes you to the I/O properties for this key. see Properties for more details.

As mentioned earlier, these switches have the capacity for 4+4 operations. The other 4 operations can be found on page 2, in the upper part of the window. When you go to this page, an identical screen is displayed with the four keys. The configuration method is exactly the same.

ATTENTION!!:
Switching between the pages is done by pressing 2 keys simultaneously. If you are using BTicino switches: Press the two upper or lower buttons of the switch simultaneously. If you use switches from Niko or the glass switches (Tastu): press the two keys on the left side or the two keys on the right side of the switch. Once this is done, the 4 keys on the 2nd page will be activated. The selection of the 2nd page takes 5 seconds, then the switch returns to the first page. You may want to use the second page of a switch for I/O’s that you do not activate regularly (e.g. shutters).

• Detecor

A bistable I/O will be activated when more movement is detected than the 'Activation-trigger'.

The I/O will be deactivated when after the extension time when there is not more movement detected than the 'Keep-trigger".

Clicking the 'Scan'-button will visualize the level of movement.

When "Only if dark"  is checked,  the I/O will only be activated when there is motion AND less light than set up in "Light Level". But when I/O is on, the light level is ignored and only motion will keep the I/O activated.

• Thermostat

The thermostat I/O will measure the room temperature and pass it to the controller. All parameters and behaviour of a thermostat can be found in our knowledge center

• Standard colors for this SWC0x:

This option allows you to set the standby and operating colors for all LEDs on pages 1 and 2.

If you click on “Use these colors as default”, the chosen colors will now be used as default. So all switches set to - Default - will use these new colors.

Clicking "Make this default for ALL SWC0x" will set these colors as default AND will also be assigned to all switches under this project.

If you want a different standard colour for each kind of I/O, the option “Colours / Mode” can be checked.
In next screen you can set the default colour/page or a specific colour for I/O’s of type On/Off, Dimmer, Shutter, Other or Scene. When data is sent to the switches, default colours will be sent depending on these settings.

• Low light
  With this option the brightness of the LEDs at the OFF position can be adjusted by moving the bar left/right (position 2-10 is recommended).

   

• With the “Short Flash on Page 2” option, when you use the 2nd page of the switch commands, the LEDs will flash to indicate that you are on page 2.

   

• The option “TH status visible on LEDs” will reduce the brightness of the LED of the thermostat I/O when the requested temperature has been reached.

  
  Finally, you will be given the opportunity to select the colors of your choice and use them for the LEDs.

An SWC can proces up to 8 alarms. They are shown in the list on the left side. In the list on the right side you can see all available alarms.

When an alarm is activated, the intelligent switch wil executed the settings as setup in 'Properties'.

One alarm can execute different actions on multiple intelligent switches.

The default settings of an alarm and an explanation of all alarm functions can be found in our knowledge center.