Aluminum SIP videophone with 1 call button

• Function description

  The Qbus video door station combines technology and design. With a press of a button, connection is made with the Qbus Control or Qbus Building Control app so a notification appears on the smartphone, tablet, or any other device where the app runs. Thanks to early-media technology, you can see who's at the door before answering the call. When answering the call, a video connection is established, along with an audio connection, allowing you to speak with the guest and grant access if desired.

  The 140° camera is subtly integrated behind the glass panel. A light sensor automatically switches the camera to night mode when needed. 

  Relay contacts: 2 contacts available.

  The Qbus door station also considers design: the combination of black anodized brushed aluminum and black glass adds extra cachet to any façade. 

  The Qbus door station is available in a version with 1 bell button (QSD01/BB) and a version with 1 bell button and keypad (QSD01K/BB), which can control relays. The provided mounting box is used for both recessed and surface wall installation. 

• Technical Specifications

  General specifications 

  • Ambient temperature:

  Operating temperature: -30°C to 65°C 

  Storage temperature: -40°C to 70°C 

  • Maximum humidity: 90%, no moisture condensation
  • Power supply: 12Vdc (1A)  or POE

  Physical specifications:

  • Protection degree: IP65
  • Installation dimensions (h x w x l): 202mm x 102mm x 31mm
  • Video doorphone (h x w x l): 216mm x 116mm x 36mm
  • Weight: approximately 139g.

  CE

  • Qbus declares that this product complies with all applicable European directives and regulations.
  • The EU declaration of conformity is available upon request.
• Sizing
• Explanation of symbols

  Equipment where protection against the risk of electric contact is not only based on basic insulation but also on additional protection such as double insulation or reinforced insulation. There is no possibility for grounding.

  Before connecting the device, it is mandatory to read the manual of the respective product. ISO7000-0434

  Power supply connection (230V) to the power supply connector. IEC 60417-5036

  CE conformity. All declarations of conformity are available upon request.

• Warranty provision

  2 years from the date of delivery. The warranty becomes void if the module has been opened! The warranty period is extended by 2 years if it was installed by a certified Qbus installer.

  In case of defects, Qbus support should be contacted by a certified installer. After registration with Qbus support, the defective module can be sent, unsealed and with a description of the defect, to our Qbus support.

  QBUS N.V. Joseph Cardijnstraat 19, 9420 Erpe-Mere, Belgium

  T +32 53 60 72 10 - F +32 53 60 72 19

  Email: [email protected]

General

• Safety Regulations

  Read the complete manual before installing and activating the module.

  ATTENTION

  • The videophone must be installed, started up, and maintained by a certified electrical installer in accordance with the applicable legal regulations of the country.
  • Before working on the videophone, the power supply must be switched off.
  • Never connect external voltages (e.g., 230Vac) to the videophone! This will cause irreparable damage!

Installation and wiring

• Installation

  The videophone can be installed as either recessed or surface-mounted.

• Power supply

  The video intercom can be powered by an external 12V DC SELV power supply or via POE (Power Over Ethernet).

• Connect

  Place the mounting frame on or in the wall with the built-in slot facing downwards. It is recommended to maintain 1m40 from the bottom of the frame to the ground.

  Ensure that the UTP cable for the network is present on site without a connector, as well as a cable for an electric lock or separate 12V DC power supply if required.

  Slide the cover plate over the cables and attach an RJ45 connector to the UTP cable.

  Connect the UTP cable to the video door phone and the separate cable to NO – COM of relay A or relay B. Opening a door lock is always best done via an INP module.

  Close the cover and use the appropriate cable grommet with sealing plate to make the video door phone watertight. Mount the assembly using the 6 supplied bolts.

  Now place the video door phone in the housing and mount it with the 4 supplied Torx anti-theft bolts in the housing using the provided screwdriver bit.

• Add a doorbell to the Qbus Control or Building Control app

  • Go to your app and click "Settings".
  • Then click "Installations".

  Click the "+" icon in the bottom-right corner.

  • Enable the toggle for "I want to add my Ubie, controller, or doorbell to an existing installation."
  • Select your installation.
  • Then click the arrow icon in the bottom-right corner.

  • Click the "Add Doorbell" button.

  • Click "Start Automatic Setup".
  • The app will now search for the connected QSD.

  • Your doorbell will now appear in the app. Click on the doorbell, then click the arrow icon.

  • Your device has been added to the Qbus Control or Building Control app.
  • You can now choose to receive doorbell calls on the device you are currently using.
  • Click "Yes" if you would like to enable this.

  • Click "My current tablet/phone" or "Other tablet/phone".
  • Your device has not been added to receive calls.

  • You can link multiple devices to receive calls. To do this, go to the detail page of your QSD. Under the "General" tab, you can add them using the "+" icon.