Linear motion and light sensor - recessed

• Function description

  The SENLine is a discrete, flat, white, round motion sensor equipped with 2 sensors that detect movement in a curtain-like detection field and measure light intensity (lux). Additionally, you can use a night function where the dimmed light circuit turns on at a lower intensity. This daylight clock function can be activated via clock times, logic, or an ordinary control. 

  The product is suitable for indoor ceiling mounting. You can directly connect this sensor to the Qbus two-wire bus using the included flexible connection cable. Configuration is done via System Manager III. 

   

  The SENLine, like every Qbus module, has a unique serial number (Prefix 0057) that is entered during configuration in the System Manager III configuration software. The programmed data remains internally stored in permanent memory. This sensor can receive firmware updates via the Qbus-bus. 

   

  The sensor can directly control various I/Os based on these sensor values: 

  • Movement: Sensitivity has two levels. A threshold for the size of the movement can be set to turn on the I/O via an "Activation trigger," and to keep the I/O on, a lower threshold of movement can be set with a "Hold trigger." The follow-up time after movement has ceased and the I/O must be turned off again is adjustable between 2 seconds and 127 minutes. A scan function allows you to visually test the current motion detection. As soon as the motion detection falls below the yellow line (hold), the follow-up time starts.
  • Lux: Threshold >= or <= adjustable between 0 and 3000 lux 

  The I/O to be controlled can be of the Bistable or Dimmer type. Thus, the sensor can directly control a dimmer based on lux measurement and motion detection. 

  A blue indicator LED is provided to display motion detection.

• Technical specifications

  General Specifications SENMoLi

  • Ambient Temperature:
  • Operating Temperature: -10°C to 50°C
  • Storage Temperature: -10°C to 60°C
  • Maximum Humidity: 95%, no moisture condensation
  • Power Supply: Bus
  • Peak Load Qbus Bus: 15mA
  • Max. Installation Height: 2,000 meters above sea level

  Electrical Protection:

  • Qbus Bus: 18Vdc low safety voltage
  • Non-toxic, in compliance with WEEE/RoHS
  • Overvoltage CAT. I (CAT.1)

  CE:

  • Qbus declares that this product complies with all applicable European directives and regulations.
  • The EU declaration of conformity is available upon request.

  Physical Specifications:

  • Housing white variant: ASA plastic, UV-resistant, black variant: ABS plastic, self-extinguishing according to UL94-V0
  • Protection Rating: IP20, EN 60529
  • Net Housing Dimensions (h x w): 31mm x 60mm
  • Housing Dimensions with Connecting Wire / Plug (h x w) 37mm x 60mm (bore diameters 40 (ideal bore diameter), 44, 48mm)
  • Dimension Cover Plate / Sensor Surface: (h x d) 1.5mm x 60mm  (bore diameters 40, 44, 48mm)
  • Built-in Version Dimensions: (h x w) 50mm x 60mm
  • Weight: approximately 30g (built-in) – 100g (surface mount)
  • Light Intensity Direct Measurement 0-1200lux
  • Detection range at 2,5m hight: 7m curtain length at ground level
• Sizing
• Explanation of symbols

  Equipment where protection against the risk of electric contact is not only based on basic insulation but also on additional protection such as double insulation or reinforced insulation. There is no possibility for grounding.

  Before connecting the device, it is mandatory to read the manual of the respective product. ISO7000-0434

  Power supply connection (230V) to the power supply connector. IEC 60417-5036

  CE conformity. All declarations of conformity are available upon request.

• Warranty provision

  Standard Warranty Period: 2 years from delivery date. The warranty is no longer valid if the module has been opened! Defective modules should be sent without seal along with a description of the defect to our service department:

  QBUS N.V. Joseph Cardijnstraat 19, 9420 Erpe-Mere, Belgium

  T +32 53 60 72 10 - F +32 53 60 72 19

  Email: [email protected]

General

• Safety regulations

  Read the full manual before installing and activating the module.

  ATTENTION

  • The module must be installed, commissioned, and maintained by a certified electrical installer in accordance with the applicable legal regulations of the country.
  • Before working on the SENMoLi, the bus power supply must be turned off.
  • Never connect external voltages (e.g., 230Vac) to the Qbus bus! This will cause irreparable damage to the modules.
  • Keep out of reach of children.
  • The module must not be opened. The warranty is void if the module is opened!

Installation and wiring

• Installation

  For the built-in version, create a round opening ideally of 40, 44, or 48mm. Connect the supplied cable to the bus cable. Then push the connections deep enough, so the sensor has sufficient free space. Open the spring clips and then gently push the sensor into the opening without applying excessive force. Do not press on the sensor surface.

  See SENTube/x for installation instructions of the stand-alone variant.

• Power supply

  The module is powered via the bus.

• BUS connection

  It is recommended to use the Qbus cable or any other cable with a minimum of 2 conductors of 1mm² as the bus cable. The green shielded EIB cable can also be used if the conductors are paired to achieve a minimum cross-section of 2 x 1mm².